Quality and properties
- Solvent-based product with special adhesion-promoting additives
- Quick-drying
- Suitable for indoors and outdoors applications
- Good resistance to outside influences
- Good flow, smooth surface
Physical and chemical datas
-
Basis of the binder: special resin
-
Colour: transparent
-
Smell: solvent
-
Degree of gloss: at measurement angle 60° acc. to DIN 67530
not applicable
-
Efficiency:
400 ml are sufficient for approx. 5 - 6 m²
-
Drying time (at 20°C, 50% relative air humidity)::
Dust-dry: after approx. 5 minutes
Dry and coatable: after approx. 15 minutes
The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
-
Temperature resistance: not applicable
-
Storage stability:
10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
-
Size:
aerosol cans, maximum nominal volume 400 ml
Environment and labelling
Environmentally sound: The products of MOTIP DUPLI are 100% free of heavy metals. The caps and packagings are made of recyclable material.
Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".
Marking/Labelling: All products made by MOTIP DUPLI comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200 and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.
Using instructions
The most presto spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label.
Before use, carefully read and observe the warning texts on the labels!
Application
Preparation of the ground:
- Clean surface from dirt, fat and silicone.
- Evtl. sand with sandpaper grain 600.
- Remove abrasive dust.
Lacquering:
- Before use, shake can for 3 minutes.
- Test spray at an invisible spot.
- Apply max. 2 thin layers.
- Spray from a distance of approx. 25 cm.
- After drying (approx. 15 minutes) coatable with acrylic, synthetic or nitro-combi lacquers.
Tips for spray painting
Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.
The aerosol can should have room temperature.
Temperature should range between +10°C and +25°C, max. air humidity 60 %.
Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!
Labelling according to Regulation (EC) No 1272/2008:
General notes:
(P101) If medical advice is needed, have product container or label at hand. (P102) Keep out of reach of children. (P210) Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. (P211) Do not spray on an open flame or other ignition source. (P251) Do not pierce or burn, aven after use. (P260) Do not breathe dust/fume/gas/mist/vapours/spray. (P410) Protect from sunlight. (P412) Do not expose to temperatures exceeding 50°C/122°F. (P501) Dispose of contents/container to …
Hazard statements:
(H222) Extremely flammable aerosol. (H229) Pressurised container: May burst if heated. (H319) Causes serious eye irritation. (H336) May cause drowsiness or dizziness.
Hazard pictograms:
Signalword: Danger
