Product information
ColorMatic 1K clear coat is a UV-resistant, fast-drying clear coat that can be applied universally at all existing base coats (solvent-based). Available in glossy, satin gloss and mat quality. Because of its very good flow and ease of polish, 1K Clear Coat glossy is highly suitable for spot repairs with solvent-based paints (e.g. ColorMatic solvent-based).
For best preparation of the surface which is to varnish, clean it thoroughly with ColorMatic Silicone Remover no. 174469 and, if required, apply a primer or filler (e.g. ColorMatic 2K Primer Filler no. 195327). We recommend using ColorMatic Spot Blender no. 114229 for spot repair on the edges.
Application:
- glossy: ideal for spot repairs and refinishing parts.
- satin gloss and mat: painting of construction parts with mat look.
Quality and Properties
- Fast drying time
- Easy application
- Can be used on all solvent-based paints
- UV resistant
Especially at 1K Clear Coat glossy
- Highly suited for spot repairs due to good flow and being easy to polish
- Light blending
- High gloss
Especially at 1K Clear Coat satin gloss and mat
- Ideal for all construction parts with a brilliant mat respectively satin gloss look
- Tip: we advice at Clear Coat mat to paint the construction parts complete
- Caution: don't polish!
Physical and Chemical Data
-
Basis of binder: Acrylic resin
-
Colour: transparent
-
Smell: solvent
-
Degree of gloss: at measurement angle 60° acc. DIN 67530
glossy: 85 - 90 GE
satin gloss: 60 GE
mat: 15-20 GE
-
Efficiency:
Depending of consistence and colour of the substrate 400 ml are sufficient for approx. 1,5 - 2,0 m²
-
Substrate:
Basecoats uni or metallic
-
Drying (at 20°C, 50% relative air humidity):
Dust-dry: after 5 - 10 minutes
Touch-dry: after 10 - 20 minutes
Cured after 24 hours
The drying time is depending on the ambient temperature, air humidity and the applied paint layer
-
Temperature resistance:
glossy to 110°C
mat to 80°C
-
Storage stability:
10 years if appropriate storage provided
-
Size:
Aerosol cans, maximum nominal volume 400 ml
-
VOC-Value:
glossy 276,4 g
satin gloss 271 g
mat 253,9 g
Enviroment and Labelling
Environmentally sound: The products of MOTIP DUPLI are 100% free of heavy metals. The caps and packagings are made of recyclable material.
Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".
Marking/Labelling: All products made by Motip Dupli comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200 and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.
Unsing Instructions
Before use, carefully read and observe the warning texts on the label!
- Solvent-based paints can be recoated with ColorMatic 1 component clear coat once they have dried for 30 minutes
- Shake can for 2 minutes
- Carry out spray test
- 1K Clear Coat glossy: For spot repairs, cover the wet edges of the clear coat ColorMatic Spot Blender
- Not suitable for recoating water-based paints (we recommend CM 2K Clear Coat high-gloss art.-no. 187216, 190469))
- Don't spray on synthetic resin areas!
- For professional use only
- Use an adequate respirator mask (we recommend type A2/P3)