Product information
For high quality matt surfaces. ColorMatic 2K Clear Coat matt offers an extremely scratch-resistance with very high resistance to petrol, UV rays and weathering. Dries quick and has a very good flow.
Application:
Ideal for the painting of parts with matt visual appearance.
Quality and Properties
- Special effect coating for tuning parts
- Wheels in high class matt finish
- Coating for plastic parts
- A high-gloss, extremely scratch-resistant 2-component clear coat – highly fuel-resistant, resistant to U.V. rays and weather influences.
- Long pot life
- Fast drying time
- Very good flow
- Convenient 200 ml can to avoid leftover
Physical and Chemical Data
-
Basis of binder: Acrylic
-
Colour: transparent
-
Smell: solvent
-
Degree of gloss: (at measurement angle 60° acc. to DIN 67530)
matt at 2 spraying passes: 20 +/- 10 gloss units (depending on the substrate and numbers of spraying passes)
-
Efficiency:
depending on consistence and colour of the ground:
200 ml are sufficient for approx. 0,3 - 0,4 m²
-
Substrate:
olvent- and water-based base coats
-
Drying time (at 20°C, 50% relative air humidity)
Dust-dry: after approx. 5 minutes
Dry to touch: after approx. 5 hours
The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
-
Temperature resistance: to 120°C
-
Storage stability:
36 month if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
-
Size:
2 components aerosol cans, maximum nominal volume 200 ml
-
VOC-value: 94 g
-
Pot-life:
24 hours at room temperature (20 - 25°C)
5 days at cool storage (6°C)
Befor using again warm up to room temperature (20 - 25°C).
See using instruction.
Enviroment and Labelling
Environmentally sound:
The products of MOTIP DUPLI are 100% free of heavy metals. The caps and packagings are made of recyclable material.
Disposal:
Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".
Marking/Labelling:
All products made by Motip Dupli comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200 and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.
Using Instructions
Before use, carefully read and observe the warning texts on the label!
Base coatings can be coated with ColorMatic 2K hi-speed clear coat matt once they have dried for 30 minutes (if surface is dust-dry)
2-3 full coats, 45µ
Leave to dry for 3 minutes between coats
Mixing A components with hardener:
Remove the protection cap from the bottom of the can and pull the pin out fully with the help of the inserted ring. This will release the knife, which will penetrate the wall of the aluminium cartridge.
The cartridge will then rotate 360 °, be completely open and release the hardener.
Shake the can vigorously to mix the A components with the hardener in the proper, predetermined ratio.
Shake can vigorously for 3 minutes
Carry out spray tests
Pot life: 24 hours (20 ° C)
Ready-to-use coating materials containing isocyanates can irritate the respiratory system and cause allergic reactions. There is a risk of sensitization with inhalation of vapours and spray mist. When dealing with substances containing isocyanates, you should observe all guidelines for using solvent-based coatings. In particular, spray mist and vapours should not be inhaled. Allergy and asthma sufferers and people who are prone to respiratory diseases should not work with isocyanates materials. For professional use only. Wear an appropriate respirator (recommended type A2/P3)
Product Safety:
Manufacturer Information
European Aerosols GmbH
Kurt-Vogelsang-Str. 6
74855 Haßmersheim
Baden-Württemberg
Deutschland
info-de@european-aerosols.com
https://www.european-aerosols.de/
