DupliColor 2K super clear lacquer high gloss D 160 (200ml)

SKU: 65-369469

Category: 2K Klarlack

GTIN: 4048500369469
HAN: 369469

DUPLI-COLOR 2K Super Clear Coat is an especially resistant, hard-drying epoxy clear lacquer. Available in high gloss quality. Offers optimal protection for high-value paintings.

18,59 €

92,97 € per 1 l

incl. 19% VAT , plus

Delivery time: 2 - 3 Workdays (DE - int. shipments may differ)

Delivery time: 2 - 3 Workdays (DE - int. shipments may differ)

Quality and Properties

High-grade, transparent 2-component clear lacquer
Epoxy quality
Isocyanate-free
Resistant to solvents, petrol and chemicals
Increased UV protection
Tough, very hard surface
Quick-drying
Very efficient
High gloss

Physical and Chemical Data

Basis of the binder: 1: Lacquer component: epoxide resin, 2. Hardener component: amine
Colour: transparent
Smell: solvent
Degree of gloss (at measurement angle 60° acc. to DIN 67530):
glossy: 85 - 95 gloss units
Efficiency:
Depending on consistence and color of the ground:
160 ml are sufficient for approx. 0.3 - 0.4 m²
Drying time (at 20°C, 50% relative air humidity):
Dust-dry: after approx. 30 minutes
Non-sticky: after approx. 2 hours
Dry to touch: after approx. 8 hours
Can be polished: after approx. 24 hours
Cured: after approx. 24 hours
The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
Temperature-resistant: up to 100°C
Storage stability:
24 months if appropriate storage provided (=10°-25°C, relative air humidity max. 60%).
Potlife after activating the hardener: 24 hours (at 20°C)
Disposal: Put only empty cans into the recycling bin. Bring cans with remainders of paint to the special refuse disposal.
Size: aerosol cans, maximum nominal volume 160 ml

Environment and labelling

Environmentally sound: The products of MOTIP DUPLI are 100% free of heavy metals. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by MOTIP DUPLI comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200 and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Using instructions

The most DUPLI-COLOR spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label.
Before use, carefully read and observe the warning texts on the label!

Preparation of the ground:

Base coatings have to be fully dry. Please observe instructions of the paint manufacturer.

Mixing the clear lacquer with the hardener:

The hardener is integrated within the spray can in a separate cartridge.
To mix the hardener with the A-component, place can upside down on even surface.
Remove protecting cap from the bottom of the can.
Take out the ring and mount the ring through the hole of the bolt.
Pull the bolt at the bottom of the can with the aid of the metal ring as far as it will go.
By a following 360° turn the cartridge will be completely opened and the hardener will be released.

Application:

Important: Shake can vigorously for 3 minutes from the audible noise of the balls in the can. This grants the optimal mixing with the hardener.
Test spray at an invisible spot.
Apply 2 – 3 coats of the clear lacquer. Allow to lift off for approx. 2 minutes after every coat.
Potlife: After activating the hardener, the clear lacquer hast to be used within 24 hours (at 20°C). The working time depends on the surrounding temperature. Higher temperatures lead to a shorter pot life, lower temperatures to a longer potlife.
Do not spray over synthetic paints!
Hint: On white or other pale surfaces there might occur slight colour deviations.

Tips for spray painting

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

Product Safety:

Manufacturer Information

European Aerosols GmbH

Kurt-Vogelsang-Str. 6

74855 Haßmersheim

Baden-Württemberg

Deutschland

info-de@european-aerosols.com

https://www.european-aerosols.de/

Item information	Value
System Components:	2C
Shipping weight:	0,22 kg
Content:	0,20 l

Contact data

Title - optional

First name

Last name

Firm - optional

E-Mail

Phone - optional

Question about item

Your question

I agree that my data as stated herein will be stored and processed for the purpose of facilitating communication with me. ()

Please note: This consent can be revoked at any time by message to us. In case of revokation your data will be deleted immediately. For more information, please read the Privacy Policy.

Spatula and putty

All accessory products for your next project!

Spatula and putty

All accessory products for your next project!

DupliColor 2K super clear lacquer high gloss D 160 (200ml)