Spray Max - 2K Acrylic Filler aerosol spray medium grey (400ml)

SKU: 15-680036

Category: Acrylic Filler

GTIN: 4015962854741

Professional, very-fast drying filler with excellent filling capacity, outstanding flow and very good insulation action in old paint jobs. Can be used for large surfaces. Pre-prime large sanded-through spots e.g. with filler primer.

£ 21,43

£ 53,57 per 1 l

incl. 19% VAT , plus (Standard)

Delivery time: 1 - 2 Workdays (DE - int. shipments may differ)

Delivery time: 1 - 2 Workdays (DE - int. shipments may differ)

Technical Information

Application:

Spot repair and part painting

Substrates:

Old paint jobs (cleaned and sanded)
Fully hardened repair paint jobs (cleaned and sanded)
Electrophoretic dip paint (cleaned and sanded)
Small sanded-through spots (cleaned and sanded)
Prime large sanded-through spots on bare metal beforehand with SprayMax 1K Filler Primer or SprayMax 2K Epoxy Primer Filler

Pretreatment:

Thoroughly grind the substrate and clean with SprayMax Silicone Remover

Activate 2K:

Shake the can well for 2 min. before activating
Remove the red push button from the cap
Turn can 180° and put the push button on the pin in the can bottom
Turn the can with the cap upside down onto a stable base
Press the red trigger button with the ball of your thumb until the limit
After activating, shake can well for 2 min. once again

Spray application:

Wet-in-wet. 2 = 40µm
Sanding filler: 3–4 = 60–80µm
Interim flash off: approx. 5–10min (until matt stripped)

Drying times:

Dust dry: 5min at 20°C
Touch dry: 15min at 20°C
Sandable: 5 h at 20°C
IR: 30–45min

Application life:

Approx. 24 hours at 20°C room temperature
The application life depends on the ambient temperature.
Higher temperatures lead to shortened, lower temperatures to a longer pot life

Post treatment:

After 5h at 20°C wet with 800-1200 grain
Sandable or after 15min flash off time at 20°C
Wet-in-wet recoatable.
Can be recoated with all commercial quality 1K or 2K topcoats, solvents and water borne paints

Gloss level:

Matt

Yield:

400ml: Approx. 0.5m² - 1m² / spray can depending on the application thickness and substrate
250ml: Approx. 0.3m² - 0.6m² / spray can depending on the application thickness and substrate

Notes:

To be used by specialists only
Wear personal protection gear (respirator type: A2/P2 safety gloves, e.g. Latex or nitrile)
After finishing the painting process, turn the can over and spray the valve empty.
Dispose of the completely empty spray cans as recyclable material

Labelling according to Regulation (EC) No 1272/2008:

General notes:

(P101) If medical advice is needed, have product container or label at hand. (P102) Keep out of reach of children. (P103) Read label before use. (P210) Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. (P211) Do not spray on an open flame or other ignition source. (P251) Do not pierce or burn, aven after use. (P261) Avoid breathing dust/fume/gas/mist/vapours/spray. (P271) Use only outdoors or in a well-ventilated area. (P273) Avoid release to the environment. (P302) IF ON SKIN: (P352) Wash with plenty of water. (P305) IF IN EYES:(P351) Rinse cautiously with water for several minutes. (P338) Remove contact lenses, if present and easy to do. Continue rinsing. (P312) Call a poison center/doctor if you feel unwell. (P333) If skin irritation or rash occurs:(P313) Get medical advice/attention. (P337) If eye irritation persists:(P313) Get medical advice/attention. (P391) Collect spillage. (P410) Protect from sunlight. (P412) Do not expose to temperatures exceeding 50°C/122°F. (P501) Dispose of contents/container to …

Hazard statements:

(H222) Extremely flammable aerosol. (H229) Pressurised container: May burst if heated. (H319) Causes serious eye irritation. (H317) May cause an allergic skin reaction. (H336) May cause drowsiness or dizziness. (H411) Toxic to aquatic life with long lasting effects.

Hazard pictograms:

Signalword: Danger

System Components:	2C
Content:	0,40 l
a1:	82477031

Contact data

Title - optional

First name

Last name

Firm - optional

E-Mail

Phone - optional

Fax - optional

Question about item

Your question

I agree that my data as stated herein will be stored and processed for the purpose of facilitating communication with me. ()

Please note: This consent can be revoked at any time by message to us. In case of revokation your data will be deleted immediately. For more information, please read the Privacy Policy.